פרטים נוספים
Compact 2 x 120 Watt Amplifier for Installation Applications
-
Compact amplifier which offers full output power across a range of loads with 2 x 120 W into 8, 4 or 2 Ohms
-
Comprehensive on-board DSP with loudspeaker processing and innovative features which enhance performance and simplifies system design and commissioning
-
Configuration software wizard for initial set-up and advanced editor for preset configuration (LUCIA connection via USB) available for Windows and Mac
-
Energy efficient with Energy Star certification for supreme green credentials and exceptionally low lifetime running costs
-
Automatic Dynamic Loudness Contouring adapts to optimize performance at any output level
-
Comprehensive DSP features with per-channel presets for high-pass filter, parametric EQ, multi-band compressor and look-ahead limiter
-
Optimized presets available for a wide range of loudspeaker models for fast configuration
-
Enhanced Bass Profile for extended LF response with small loudspeakers
-
Proprietary Auto Load Sense automatically sets VPL (Voltage Peak Limiter) for optimum performance with any connected load
-
Efficient Class-D amplifier with low distortion and minimal heat dissipation
-
Compact form factor in a half-rack, 1U chassis with supplied bracket for discreet on-wall mounting
-
Configurable GPIO port for remote control (e.g. wall panel) for channel switching, level control and integration with paging systems
-
Comprehensive circuit protection for fail safe operation, including short circuit, thermal and undervoltage protection
-
Universal power supply supports 100 - 240 V AC at 50 or 60 Hz
-
Intelligent fan control for silent operation at idle and at lower output levels
-
Front panel power and fault indication as well as per-channel signal LED and attenuation knob
-
Balanced high quality analog inputs and amplifier outputs on detachable screw terminals
-
Parallel analogue input on unbalanced RCA connectors with optimized gain for mobile and other unbalanced sources
-
Rackmount kit, pole-mount kit and wall panel kits available as accessories
General
| Number of amplifier channels |
2
|
| Max total output all channels driven |
240 W
|
| Max output voltage per channel 1 |
43.8 V peak
|
| Max output current per channel |
7.8 Arms
|
Max output power (all channels driven)
| 2 ohms |
120 W
|
| 4 ohms |
120 W
|
| 8 ohms |
120 W
|
| 16 ohms |
60 W
|
Performance
| THD 20 Hz - 20 kHz at 1 W into 8 ohms |
<0.3%
|
| THD at 1 kHz and 1 dB below clipping |
<0.2%
|
| Signal to Noise Ratio |
>101 dBA
|
| Channel separation (Crosstalk) at 1 kHz |
>60 dBA
|
| Frequency Response |
5 Hz - 22 kHz
|
| Input impedance |
10 kOhm
|
| Common Mode Rejection (CMR) |
40 dB
|
Gain, Sensitivity and Limiters
| VPL for 16 ohm mode |
43.8 Vpeak
|
| VPL for 8 ohm mode |
43.8 Vpeak
|
| VPL for 4 ohm mode |
31 Vpeak
|
| VPL for 2 ohm mode |
22 Vpeak
|
| Sensitivity, balanced input |
4 dBu / 1.23 Vrms
|
| Sensitivity, RCA input |
-2 dBu / 0.62 Vrms
|
| Input headroom for clip, balanced 2 |
12 dBu / 3.09 Vrms
|
| Input headroom for clip, RCA 2 |
6 dBu / 1.55 Vrms
|
Connectors and Buttons
| Input connectors (per ch.) |
3 - pin detachable screw terminals, electronically balanced
|
| Input connectors (ch. 1 & 2) |
Unbalanced RCA type
|
| Output connectors (per ch.) |
2 - pin detachable screw terminals
|
| GPI (power control input) 3 |
2 channels of voltage sense type. 4 pins in a detachable screw terminal. Default for gain.
|
| GPO (power state output) 3 |
Contact closure type, 2 pins in a detachable screw terminal Default for external monitoring of fault/protection/power off
|
| RS232 |
Can be controlled and monitored by third parties via RS232 using both the GPI pins
|
| USB |
For firmware update and configuration for the matrix models
|
| Level adjustment (per channel) 3 |
Front panel potentiometer, detented from -inf to 0 dB
|
Processing Features
| Input processing block 4 |
4 EQ sections per input
|
| Mix matrix routing block 4 |
2 in - 2 out mix-matrix controllable from GPI
|
| Output processing block 4 |
4 EQ sections per output (presets available for many loudspeakers) User adjustable output look ahead limiter ADLC (Adaptive ISO 226 compensation)
|
| Latency from any input to any output |
User adjustable from 9.15 to 137 ms
|
Power
| Nominal voltage |
100 – 240 VAC
|
| Operating voltage |
85 – 265 VAC
|
| Standby consumption |
<1 W
|
| Mains connector |
IEC inlet
|
| Cooling |
One fan, no filter required, front to rear airflow, temperature controlled speed. Can stay off if the sustained power average stays below 2 × 6 W and the ambient temperature is below 25 C
|
| Auto mode |
The power state is controled automatically by the audio signal
|
Dimensions
| Dimensions |
W: 216 mm (8.5”), H: 44 mm (1 U), D: 280 mm (11”)
|
Weight
Finish
| Finish |
Black aluminum front and black steel chassis
|